Section: User Commands (1)
Updated: Taylor UUCP 1.07
cu - Call up another system
[ options ] [ system | phone | "dir" ]
command is used to call up another system and act as a dial in
terminal. It can also do simple file transfers with no error
takes a single argument, besides the options. If the argument is the
string "dir" cu will make a direct connection to the port. This may
only be used by users with write access to the port, as it permits
reprogramming the modem.
Otherwise, if the argument begins with a digit, it is taken to be a
phone number to call. Otherwise, it is taken to be the name of a
system to call. The
option may be used to name a system beginning with a digit, and the
option may be used to name a phone number that does not begin with a
locates a port to use in the UUCP configuration files. If a simple
system name is given, it will select a port appropriate for that
-p, --port, -l, --line, -s
options may be used to control the port selection.
When a connection is made to the remote system,
forks into two processes. One reads from the port and writes to the
terminal, while the other reads from the terminal and writes to the
provides several commands that may be used during the conversation.
The commands all begin with an escape character, initially
(tilde). The escape character is only recognized at the beginning of
a line. To send an escape character to the remote system at the start
of a line, it must be entered twice. All commands are either a single
character or a word beginning with
recognizes the following commands:
Terminate the conversation.
- ~! command
Run command in a shell. If command is empty, starts up a shell.
- ~$ command
Run command, sending the standard output to the remote system.
- ~| command
Run command, taking the standard input from the remote system.
- ~+ command
Run command, taking the standard input from the remote system and
sending the standard output to the remote system.
- ~#, ~%break
Send a break signal, if possible.
- ~c directory, ~%cd directory
Change the local directory.
- ~> file
Send a file to the remote system. This just dumps the file over the
communication line. It is assumed that the remote system is expecting
Receive a file from the remote system. This prompts for the local
file name and for the remote command to execute to begin the file
transfer. It continues accepting data until the contents of the
variable are seen.
- ~p from to, ~%put from to
Send a file to a remote Unix system. This runs the appropriate
commands on the remote system.
- ~t from to, ~%take from to
Retrieve a file from a remote Unix system. This runs the appropriate
commands on the remote system.
- ~s variable value
variable to the given value. If value is not given, the variable is
- ~! variable
Suspend the cu session. This is only supported on some systems. On
systems for which ^Z may be used to suspend a job,
will also suspend the session.
Turn off XON/XOFF handling.
Turn on XON/XOFF handling.
List all the variables and their values.
List all commands.
also supports several variables. They may be listed with the
command, and set with the
The escape character. Initially
If this variable is true,
will delay for a second after recognizing the escape character before
printing the name of the local system. The default is true.
The list of characters which are considered to finish a line. The
escape character is only recognized after one of these is seen. The
default is carriage return, ^U, ^C, ^O, ^D, ^S, ^Q, ^R.
Whether to transfer binary data when sending a file. If this is
false, then newlines in the file being sent are converted to carriage
returns. The default is false.
A string used before sending a binary character in a file transfer, if
variable is true. The default is ^V.
Whether to check file transfers by examining what the remote system
echoes back. This probably doesn't work very well. The default is
The character to look for after sending each line in a file. The
default is carriage return.
The timeout to use, in seconds, when looking for a character, either
when doing echo checking or when looking for the
character. The default is 30.
The character to use delete a line if the echo check fails. The
default is ^U.
The number of times to resend a line if the echo check continues to
fail. The default is 10.
The string to write after sending a file with the
command. The default is ^D.
The string to look for when receiving a file with the
command. The default is $, which is intended to be a typical shell
Whether to print accumulated information during a file transfer. The
default is true.
The following options may be given to
- -e, --parity=even
Use even parity.
- -o, --parity=odd
Use odd parity.
Use no parity. No parity is also used if both
- -h, --halfduplex
Echo characters locally (half-duplex mode).
Turn off XON/XOFF handling (it is on by default).
- -E char, --escape char
Set the escape character. Initially
(tilde). To eliminate the escape character, use
- -z system, --system system
The system to call.
- -c phone-number, --phone phone-number
The phone number to call.
- -p port, --port port
Name the port to use.
- -a port
- -l line, --line line
Name the line to use by giving a device name. This may be used to
dial out on ports that are not listed in the UUCP configuration files.
Write access to the device is required.
- -s speed, --speed speed
The speed (baud rate) to use.
Where # is a number, equivalent to
- -n, --prompt
Prompt for the phone number to use.
Enter debugging mode. Equivalent to
- -x type, --debug type
Turn on particular debugging types. The following types are
recognized: abnormal, chat, handshake, uucp-proto, proto, port,
config, spooldir, execute, incoming, outgoing. Only abnormal, chat,
handshake, port, config, incoming and outgoing are meaningful for
Multiple types may be given, separated by commas, and the
option may appear multiple times. A number may also be given, which
will turn on that many types from the foregoing list; for example,
is equivalent to
may be used to turn on all debugging options.
- -I file, --config file
Set configuration file to use. This option may not be available,
depending upon how
- -v, --version
Report version information and exit.
Print a help message and exit.
This program does not work very well.
Ian Lance Taylor