The optional hostname argument is the name or the IP address of the remote host. scli talks to this host's SNMP agent on the default port number 161 using the SNMP over UDP transport mapping.
The optional community argument is the community string used to communicate with the remote SNMP agent. The default string is public. Please check the configuration of the SNMP agent to get a clue about the community string to use, if the default community string does not work.
scli supports recursive command evaluation. When a command is entered which is not a leaf of the command tree, then the interpreter will recursively invoke all commands in the subtree identified by the entered command. In particular, entering show will cause scli to retrieve and display all information accessible from the remote SNMP agent. 100 scli version 0.4.0 (c) 2001-2010 Juergen Schoenwaelder
The 3com scli mode allows to manipulate virtual lans (vlans) on 3com bridges. It is based on the PRODUCTMIB which is implemented at least on 3Com SuperStack II switches.
The create 3com bridge vlan command is used to create a new virtual LAN with the given <vlanid> and <name>.
The delete 3com bridge vlan command deletes all selected virtual LANs. The regular expression <regexp> is matched against the virtual LAN names to select the vlans that should be deleted.
The set 3com bridge vlan name command changes the name of a virtual LAN.
The set 3com bridge vlan ports command allows to assign ports to port-based virtual LANs. The regular expression <regexp> is matched against the virtual LAN names to select the vlans that should be modified. The <ports> argument contains a comma separated list of port numbers or port number ranges, e.g. 1,5,7-8.
The show 3com bridge vlan info command shows summary information about all selected virtual LANs. The optional regular expression <regexp> is matched against the virtual LAN names to select the virtual LANs of interest. The command generates a table with the following columns:
VLAN virtual LAN number
STATUS status of the virutal LAN (see below)
NAME name of the virutal LAN
INTERFCE virtual LAN interface number
PORTS ports assigned to the virtual LAN
The status is encoded in two characters. The first character indicates the status of the row (A=active, S=not in service, R=not ready). The second character indicates virutal LAN type (P=port, I=IP-subnet, O=protocol, S=src address, D=dst address).
The dump 3com bridge vlan command generates a sequence of scli commands which can be used to restore the virtual LAN configuration.
The atm scli mode is based on the ATM-MIB as published in RFC 2515. This mode is intended to display and configure ATM parameters.
The show atm interface info command displays summary information for all selected ATM interfaces. The optional regular expression <regexp> is matched against the interface descriptions to select the interfaces of interest. The command generates a table with the following columns:
INTERFACE network interface number
DESCRIPTION description of the network interface
The show atm interface details command describes the selected ATM interfaces in more detail. The optional regular expression <regexp> is matched against the interface descriptions to select the interfaces of interest.
The scli bridge mode is based on the BRIDGE-MIB as published in RFC 4188 and the Q-BRIDGE-MIB as published in RFC 4363. It provides commands to browse information specific to IEEE 802.1 LAN bridges (also known as layer two switches).
The show bridge info command displays summary information about a bridge, such as the number of ports and the supported bridging functions and associated parameters.
The show bridge ports command displays information about the bridge ports.
The show bridge stp ports command displays information about the bridge ports which participate in the spanning tree protocol. The command generates a table with the following columns:
PORT port number
PRIO spanning tree priority of the port
STATE spanning tree status of the port
P-COST path costs for this port
D-ROOT designated root port
D-COST designated costs
D-BRIDGE designated bridge
D-PORT designated port
The status is encoded in two characters. The first character indicates whether STP on the port is enabled (E) or disabled (D). The second character indicates the current status (D=disabled, B=blocking, I=listening, L=learning, F=forwarding, X=broken).
The show bridge forwarding command displays the forwarding data base used by transparent bridges. The command generates a table with the following columns:
PORT port number
STATUS status of the forwarding entry
ADDRESS address associated with the port
NAME name of the address (where known)
VENDOR vendor info derived from the address
The show bridge filter command shows filtering information.
The show bridge stats command displays per port statistics for transparent bridges. The command generates a table with the following columns:
PORT port number
I-FPS input frames per second
O-FPS output frames per second
D-FPS discarded frames per second
DESCRIPTION description of the port
The monitor bridge stats command shows the same information as the show bridge stats command. The information is updated periodically.
The show bridge vlan info command shows summary information about configured VLANs. The command generates a table with the following columns:
VLAN VLAN number (between 1 and 4094)
STATUS status of the VLAN
NAME name of the VLAN
PORTS ports assigned the the VLAN
The show bridge vlan details command describes the selected VLANs in detail. The optional regular expression <regexp> is matched against the VLAN names to select the VLANs of interest.
The create bridge vlan command creates a new vlan with the given <id> and name <name>.
The delete bridge vlan command deletes all vlans whose vlan name matches the regular expression <regexp>.
The cisco scli mode is used to display and configure cisco parameters. It also supports retrieval of accounting data from devices that support the old cisco accounting mib. This mode is based on the OLD-CISCO-IP-MIB published in May 1994.
The show cisco processes command displays information about all processes running on a CISCO device. The command generates a table with the following columns:
CPU processor executing a given process
PID process indentification number on a CPU
P priority of the process
MEMORY memory used by the process
TIME CPU time used by the process
COMMAND command executed by the process
The show cisco ip accounting info command displays general status information concerning the simple cisco IPv4 accounting mechanism supported by many older cisco devices. In particular, it displays the starting point of the current and snapshot data tables, information about the available accounting capacity, and statistics about lost bytes and packets.
cisco IP current accounting data
The show cisco ip accounting current raw command displays the raw accounting data retrieved from the current table. The command generates a table with the following columns:
SOURCE source IPv4 address in dotted notation
DESTINATION destination IPv4 address in dotted notation
PACKETS packets sent from source to destination
BYTES bytes sent from source to destination
cisco IP snapshot accounting data
The show cisco ip accounting snapshot raw command displays the raw accounting data retrieved from the snapshot table. The command generates a table with the following columns:
SOURCE source IPv4 address in dotted notation
DESTINATION destination IPv4 address in dotted notation
PACKETS packets sent from source to destination
BYTES bytes sent from source to destination
cisco IP current accounting data
cisco IP snapshot accounting data
The set cisco ip accounting checkpoint command takes a snapshot of the current accounting table by copying it to the snapshot accounting table. The current accounting table is reinitialized before it is updated again. The command returns the serial number of the snapshot.
The show cisco dot11 interface info command displays information about all IEEE 802.11 interfaces on a CISCO device. The command generates a table with the following columns:
IFACE network interface number
SPEED speed in bits per second
NAME name of the network interface
CLNT number of associated clients
BRDG number of assiciated bridges
RPRT number of assiciated repeaters
ASSCI total number of associated stations
ASSCO total number of deassociated stations
ROAMI total number of roamed-in stations
ROAMO total number of roamed-away stations
AUTHI total number of authenticated stations
AUTHO total number of deauthenticated stations
The show cisco dot11 clients stats command displays information about all IEEE 802.11 clients associated with a CISCO device. The command generates a table with the following columns:
IF network interface number
SSID SSID to which client is associated
ADDRESS client MAC address
IPv4-ADDRESS clients IPv4 address (if supplied)
SGNL clients signal strength
UPTIME lifetime of clients association
I-BPS input bytes per second
O-BPS output bytes per second
ERR errors per second
The monitor cisco dot11 clients stats command shows the same information as the show cisco dot11 clients stats command. The information is updated periodically.
The scli disman mode is based on the DISMAN-SCRIPT-MIB as published in RFC 3165 and the DISMAN-SCHEDULE-MIB as published in RFC 3231. It allows to browse and configure distributed managers.
languages supported by the distributed manager
script summary information
scripts installed at the distributed manager
launch summary information
launch buttons installed on the distributed manager
summary information about running scripts
running scripts on the distributed manager
The show schedule info command displays summary information about the scheduled actions.
schedules on the distributed manager
The dump schedule command generates a sequence of scli commands which can be used to restore the schedule configuration.
scheduler information
The entity scli mode is based on the ENTITY-MIB as published in RFC 2737. It provides commands to browse the physical entities or physical components that make up a managed system.
The show entity info command displays summary information about the physical entities that compose the system. The command generates a table with the following columns:
ENTITY entity number
CLASS class of the entity (see below)
NAME name of the entity
DESCRIPTION description of the entity
The show entity details command describes the physical entities in more detail.
The show entity containment command displays the physical entity containment hierarchy.
The show entity sensors command describes the physical sensor entities in more detail.
The ethernet scli mode is based on the EtherLike-MIB as published in RFC 2665 and the MAU-MIB as published in RFC 2668.
The show ethernet mau command displays information about the medium attachment units (MAUs) for each ethernet port. The command generates a table which has the following columns:
INTERFACE network interface number
MAU medium attachment unit number per interface
STATUS status of the medium attachment unit
MEDIA media availability
JABBER jabber state of the medium attachment unit
AUTONEG autonegation capabilities
TYPE type of the medium attachment unit
The show ethernet stats command displays ethernet specific statistics for each ethernet interface. The command outputs a table which has the following columns:
INTERFACE network interface number
ALIGN alignement errors per second
FCS frame check sequence errors per second
RCV MAC receive errors per second
LONG frames exceeding maximum frame size per second
DEFER deferred transmission per second
SCOL single collisions per second
MCOLR multiple collisions per second
XCOL excessive collisions per second
LCOL late collisions per second
XMIT MAC transmit errors per second
CARR carrier sense errors per second
The monitor ethernet stats command shows the same information as the show ethernet stats command. The information is updated periodically.
The hp scli mode is used to display and configure hp parameters.
The scli interface mode is based on the IF-MIB as published in RFC 2863. It provides commands to browse, monitor and configure arbitrary network interfaces.
The set interface status command modifies the administrative status of all selected interfaces. The regular expression <regexp> is matched against the interface descriptions to select the interfaces of interest. The <value> parameter must be one of the strings "up", "down", or "testing".
The set interface alias command assigns the alias name <string> to the selected interfaces. The alias name provies a non-volatile handle which can be used by management applications to better identify interfaces. The regular expression <regexp> is matched against the interface descriptions to select the interfaces.
The set interface notifications command controls whether the selected interfaces generate linkUp and linkDown notifications. The regular expression <regexp> is matched against the interface descriptions to select the interfaces. The <value> parameter must be one of the strings "enabled" or "disabled".
The set interface promiscuous command controls whether the selected interfaces operate in promiscuous mode or not. The regular expression <regexp> is matched against the interface descriptions to select the interfaces. The <bool> parameter must be one of the strings "true" or "false".
The show interface info command displays summary information for all selected interfaces. The optional regular expression <regexp> is matched against the interface descriptions to select the interfaces of interest. The command generates a table with the following columns:
INTERFACE network interface number
STATUS interface status (see below)
MTU maximum transfer unit
TYPE type of the network interface
SPEED speed in bits per second
NAME name of the network interface
DESCRIPTION description of the network interface
The status is encoded in four characters. The first character indicates the administrative status (U=up, D=down, T=testing). The second character indicates the operational status (U=up, D=down, T=testing, ?=unknown, O=dormant, N=not-present, L=lower-layer-down). The third character indicates whether a connector is present (C=connector, N=none) and the fourth character indicates whether the interface is in promiscuous mode (P=promiscuous, N=normal).
The show interface details command describes the selected interfaces in detail. The optional regular expression <regexp> is matched against the interface descriptions to select the interfaces of interest.
The show interface stack command shows the stacking order of the interfaces. The command generates a table with the following columns:
INTERFACE network interface number
STACK indication of the stacking order
TYPE type of the network interface
DESCRIPTION description of the network interface
The show interface stats command displays network interface statistics for all selected interfaces. The optional regular expression <regexp> is matched against the interface description to select the interfaces. The command outputs a table which has the following columns:
INTERFACE network interface number
STATUS interface status (see above)
I-BPS input bytes per second
O-BPS output bytes per second
I-PPS input packets per second
O-PPS output packets per second
I-ERR input errors per second
O-ERR output errors per second
I-DIS input packets discarded per second
O-DIS output packets discarded per second
I-UNK input packets with unknown protocols per second
DESCRIPTION description of the network interface
The monitor interface stats command shows the same information as the show interface stats command. The information is updated periodically.
The loop interface stats command shows the same information as the show interface stats command. The information is updated periodically.
The check interface status command checks the status of interfaces. The optional regular expression <regexp> is matched against the interface description to select the interfaces In particular, the check interface status commands detects fault conditions if (a) ifAdminStatus is not down and ifOperStatus is down or (b) ifAdminStatus is down and ifOperStatus is not down and not notPresent
The dump interface command generates a sequence of scli commands which can be used to restore the interface configuration.
The ip scli mode is based on the IP-MIB as published in RFC 2011, the IP-FORWARD-MIB as published in RFC 2096, the IP-TUNNEL-MIB as published in RFC 2667 and the RFC1213-MIB as published in RFC 1213. It provides commands to browse, monitor and configure IP protocol engines.
The set ip forwarding command controls whether the IP protocol engine forwards IP datagrams or not. The <value> parameter must be one of the strings "enabled" or "disabled".
The set ip ttl command can be used to change the default time to live (TTL) value used by the IP protocol engine. The <number> parameter must be a number between 1 and 255 inclusive.
The show ip info command displays parameters of the IP protocol engine, such as the default TTL or whether the node is forwarding IP packets.
The show ip forwarding command displays the IP forwarding data base. The command generates a table with the following columns:
DESTINATION destination address and prefix
NEXT-HOP next hop towards the destination
TOS type of service selector
TYPE type (direct/indirect) of the entry
PROTO protocol which created the entry
INTERFACE interface used for forwarding
The show ip addresses command displays the IP addresses assigned to network interfaces. The command generates a table with the following columns:
ADDRESS IP address
PREFIX IP address prefix length
NAME name of the IP address
INTERFACE network interface number
DESCRIPTION description of the network interface
The show ip tunnel command displays information about existing IP tunnels.
The show ip mapping command displays the mapping of IP address to lower layer address (e.g., IEEE 802 addresses). The command generates a table with the following columns:
INTERFACE network interface number
STATUS status of the mapping entry
ADDRESS IP address
ADDRESS lower layer address
The dump ip command generates a sequence of scli commands which can be used to restore the IP configuration.
The scli isdn mode is based on the ISDN-MIB as published in RFC 2127.
The show isdn bri command shows information about the ISDN basic rate interfaces. The command outputs a table which has the following columns:
INTERFACE network interface number
TYPE type of the ISDN interface
TOPOLOGY line topology
MODE interface mode (te/nt)
SIGNALING signaling mode (active/inactive)
DESCRIPTION description of the network interface
The show isdn bearer command shows information about the ISDN B (bearer) channels.
The show isdn endpoints command shows information about the ISDN endpoints.
The netsnmp scli mode is used to display and configure netsnmp specific parameters. It is based on the UCD-SNMP-MIB.
The set netsnmp debugging command controls whether the agent generates debug messages or not. The <value> parameter must be one of the strings "enabled" or "disabled".
The set netsnmp restart command restarts the agent.
The show netsnmp info command shows general information about the netsnmp/ucdsnmp agent such as the version number and the software configuration.
The show netsnmp load command shows the load indices of the system. This is usually the length of the queue in front of the processor(s) averaged over some time interval.
The show netsnmp exec command shows information about pre-configured commands that can be invoked.
The show netsnmp proc command shows information about which processes netsnmp watches.
The dump netsnmp command generates a sequence of scli commands which can be used to restore the netsnmp specific configuration.
The nortel scli mode allows to manipulate virtual LANs (vlans) on nortel bridges. It is based on the RAPID-CITY MIB which is implemented at least on the baystack bridges.
The create nortel bridge vlan command is used to create a new virtual LAN with the given <vlanid> and <name>.
The delete nortel bridge vlan command deletes all selected virtual LANs. The regular expression <regexp> is matched against the virtual LAN names to select the vlans that should be deleted.
The set nortel bridge vlan name command changes the name of a virtual LAN.
The set nortel bridge vlan ports command allows to assign ports to port-based vlans. The regular expression <regexp> is matched against the vlan names to select the vlans that should be modified. The <ports> argument contains a comma separated list of port numbers or port number ranges, e.g. 1,5,7-8.
The set nortel bridge vlan default command allows to assign ports to a default vlan. The <string> argument is matched against the vlan names to select the vlan. The <ports> argument contains a comma separated list of port numbers or port number ranges, e.g. 1,5,7-8.
The show nortel bridge vlan info command shows summary information about all selected virtual LANs. The optional regular expression <regexp> is matched against the virtual LAN names to select the virtual LANs of interest. The command generates a table with the following columns:
VLAN number of the virtual LAN
STATUS status of the virtual LAN (see below)
NAME name of the virtual LAN
PORTS ports assigned to the virtual LAN
The status is encoded in four characters. The first character indicates the status of the row (A=active, S=not in service, R=not ready). The second character indicates virtual LAN type (P=port, I=IP-subnet, O=protocol, S=src address, D=dst address). The third character indicates the priority of the virtual LAN (H=high, N=normal) and the fourth character indicates whether routing is enabled (R=routing, N=no routing).
The show nortel bridge vlan details command describes the selected vlans in more detail. The optional regular expression <regexp> is matched against the vlan names to select the vlans of interest.
The show nortel bridge vlan ports command shows information for each vlan port. The command generates a table with the following columns:
PORT port number
FLAGS port vlan flags (see below)
DEFAULT default vlan number
VLANS vlan numbers the port is member of
The flags are encoded in four characters. The first character indicates the port type (A=access, T=trunk). The second character indicates whether the port tags frames (T=tagging, N=none). The third character indicates whether the port discards tagged frames (D=discard, N=none) and the fourth character indicates whether the port discards untagged frames (D=discard, N=none).
The dump nortel bridge vlan command generates a sequence of scli commands which can be used to restore the virtual LAN configuration.
The scli ospf mode is used to display and configure OSPF parameters.
show OSPF areas
general OSPF information
show OSPF interfaces
The scli printer mode is based on the Printer-MIB as published in RFC 1759 and some updates currently being worked on in the IETF Printer MIB working group.
The set printer operator command configures the name of the person responsible for operating a printer. As a convention, the phone number, fax number or email address should be indicated by the tel:, fax: and mailto: URL schemes.
The show printer info command shows general information about the printer including global status information.
The show printer paths command shows information about the media paths of a printer.
The show printer inputs command shows information about the input sub-units of a printer which provide media for input to the printing process.
The show printer output command shows information about the output sub-units of a printer capable of receiving media delivered from the printing process.
The show printer markers command shows information about the marker sub-units of a printer which produce marks on the print media.
The show printer colorants command shows information about the colorant sub-units of a printer which produce marks on the print media.
The show printer supplies command shows information about the supplies which are consumed and the waste produced by the markers of a printer.
The show printer interpreters command shows information about the page description language and control language interpreters supported by the printer.
The show printer channels command shows information about the channels which can be used to submit data to the printer.
The show printer covers command shows information about the covers of a printer.
The show printer display command shows the current contents of the display attached to the printer. The command generates a table with the following columns:
PRINTER logical printer number
LINE display line number
TEXT contents of the display line
The show printer lights command shows the current status of the lights attached to the printer. The command generates a table with the following columns:
PRINTER logical printer number
LIGHT number identifying the light/led
DESCRIPTION description of the light/led
STATUS current status (on, off, blink)
COLOR current color of the light
The show printer alerts command displays the list of active printer alerts including the alert code, the alert severity, the alert description, the alert time, the alert location and the personel required to handle the alert.
The monitor printer display command shows the same information as the show printer display command. The information is updated periodically.
The monitor printer lights command shows the same information as the show printer lights command. The information is updated periodically.
The monitor printer alerts command shows the same information as the show printer alerts command. The information is updated periodically.
The run printer reboot command resets the printed.
The rs232 scli mode is based on the RS-232-MIB as published in RFC 1659.
The show rs232 details command describes the selected RS 232 interfaces in detail.
The scli mode provides commands that can be used to display and manipulate the internal state of the scli interpreter.
The open command establishes an association to a remote SNMP agent. The <nodename> argument is the DNS name or the IP address of the remote node. Scli will try to talk to the SNMP agent on this node by using the default port number (usually 161) and the default transport mapping (usually SNMP over UDP). The optional <community> argument is the community string needed to communicate with the remote SNMP agent. The default community string is "public". Opening an association while an association is already established is not considered an error. The existing established association will be closed automatically before an attempt to create a new association is started.
The close command closes an established association to a remote SNMP agent. Invoking the close command when no association is established is not considered an error and will do just nothing.
The run scli walk command is a debugging utility which simply performs a MIB walk. Note that scli does not have general MIB knowledge and hence the output requires some post-processing.
The run scli scan command is a utility which scans an IPv4 address space identified by the <network> argument. The <network> must be specified in the format <ipv4address>/<prefix>. The optional <community> argument is the community string needed to communicate with the remote SNMP agent. The default community string is "public".
The run scli sleep command simply sleeps for the given amount of seconds.
The create scli plugin command dynamically loads an scli mode into a running scli process. This can be used to dynamically extend scli with modules coming from other sources. Dynamic loadable modules also simplify the development and management of site-specific modules.
The delete scli plugin command removes a previously loaded modules from a running scli process.
The exit command terminates the scli interpreter. An end of file in the standard input stream will also terminate the the scli interpreter.
The help command displays some help information including a list of all top-level scli commands.
The history command displays the scli command history list with line numbers.
The create scli alias command creates the alias <name> for the scli command (fragment) <value>. If the alias <name> already exists, then the new <value> will be assigned to the existing alias.
The delete scli alias command removes previously defined aliases from the scli interpreter. The regular expression <regexp> is matched against all alias names in order to select the aliases that are deleted.
The create scli interp command creates a new internal scli interpreter with the name <name>.
The delete scli interp command deletes previously defined scli interpreters from the main scli interpreter. The regular expression <regexp> is matched against all alias names in order to select the interpreter(s) to be removed.
The set scli regex command controls how scli matches regular expressions. The optional regular expression <regexp> is matched against the regular expression options. A successful match turns a regular expression option on while an unsuccessful match turns a regular expression option off. Invoking the command without the <regexp> argument will turn all regular expression options off. The currently defined regular expression options are "extended" for POSIX extended regular expressions and "case-insensitive" for case insensitive matches.
The set scli debugging command sets the debugging level of the SNMP engine. The optional regular expression <regexp> is matched against the debugging levels. A successful match turns a debugging level on while an unsuccessful match turns a debugging level off. Invoking the command without the <regexp> argument will turn all debugging levels off. The currently defined debugging levels are "session" for the SNMP session layer, "request" for the SNMP request handling layer, "transport" for the SNMP transport layer, "packet" for the SNMP packet layer, and "asn1" for the ASN.1 coding layer.
The set scli pager command defines the shell command which is used as a pager if the output produced by an scli command does not fit on a single screen. The output is passed to the <pager> shell command via its standard input stream.
The set scli retries command defines the number of SNMP request retries before giving up requesting a certain object.
The set scli timeout command defines the number milliseconds between subsequent SNMP request retries.
The set scli format command defines the output format used by subsequent scli commands. The currently supported formats are "scli" and "xml". The "scli" format is the default output format and described in this documentation. The "xml" output format is experimental and therefore not described here.
The set scli mode command defines the scli mode used by subsequent scli commands. Setting the mode to "protocol" will force scli to work in protocol mode. Setting the mode to "normal" causes scli to work in normal mode where certain status messages are suppressed.
The show scli info command displays the current status of the scli interpreter.
The show scli command info command displays summary information about scli commands. The optional regular expression <regex> is matched against the command names to select the scli commands.
The show scli command details command displays detailed information about scli commands. The optional regular expression <regex> is matched against the command names to select the scli commands.
The show scli command tree command displays the scli command tree. The full command syntax is displayed for each leaf node.
The show scli aliases command lists all scli command aliases. The first column in the generated table lists the aliase names while the second column shows the alias values.
The show scli modes command shows information about the scli modes. An scli mode is a logical grouping of related commands (e.g., all commands that deal with printers). The optional regular expression <regex> can be use to select a subset of the available scli modes.
The show scli schema command produces xml schema definitions for the selected scli modes. An scli mode is a logical grouping of related commands (e.g., all commands that deal with printers). The optional regular expression <regex> can be use to select a subset of the available scli modes.
The show scli alarm info command displays summary information about all known alarms.
The snmp scli mode is based on the SNMPv2-MIB as published in RFC 1907, the SNMP-FRAMEWORK-MIB as published in RFC 3411, the SNMP-USER-BASED-SM-MIB as published in RFC 3414, the SNMP-VIEW-BASED-ACM-MIB as published in RFC 3415, the SNMP-TARGET-MIB as published in RFC 3413, the SNMP-NOTIFICATION-MIB as published in RFC 3413, and theNOTIFICATION-LOG-MIB as published in RFC 3014.
The create snmp vacm member commands can be used to assign new members (security names) to vacm groups. New groups are created if they do not exist.
The delete snmp vacm member commands can be used to delete members (security names) from vacm groups. Groups are deleted if the last member is deleted.
The create snmp usm user commands can be used to create a new user by cloning an existing template.
The set snmp authentication traps command controls whether the SNMP engine generates authentication failure notifications. The <value> parameter must be one of the strings "enabled" or "disabled".
The show snmp engine command displays information about the SNMP protocol engine such as the number of boots, the current time relative to the last boot and the maximum message size.
The show snmp resources command displays information about the MIB resources supported by the SNMP agent.
The show snmp vacm member command displays the mapping of security names to group names. The command generates a table with the following columns:
ROW row storage type and status
MOD security model
NAME member name (security name)
GROUP name of the vacm group
The show snmp vacm access command display the access control rules for the security groups. The command generates a table with the following columns:
ROW row storage type and status
GROUP security group name
MOD security model
LVL security level (--, a-, ap)
CTX context name
MATCH match (exact or prefix)
READ view name for read access
WRITE view name for write access
NOTIFY view name for notification
The show snmp vacm views command displays MIB view definitions. The command generates a table with the following columns:
ROW row storage type and status
VIEW view name
TYPE access to the view subtree (incl/excl)
PREFIX object identifier wildcard prefix
The show snmp usm users command displays the configured users. The command generates a table with the following columns:
ROW row storage type and status
USER USM user name
NAME security name of the USM user
AUTH authentication protocol
PRIV privacy protocol
The show snmp target addresses command displays information about the configured SNMP target addresses. The command generates a table with the following columns:
ROW row storage type and status
TARGET target name
DOMAIN transport domain
ADDRESS transport address
TMOUT timeout value in ms
RETRY number of retries
PARAMS associated parameters
TAGS tag list
The show snmp target parameters command displays information about the configured SNMP target parameters. The command generates a table with the following columns:
ROW row storage type and status
PARAMS parameter name
NAME security name
The show snmp notification targets command displays information about the configured SNMP notification targets. The command generates a table with the following columns:
ROW row storage type and status
NAME notification target name
TYPE notification type
TAG tag reference to targets
The show snmp contexts command displays information about the available SNMP contexts.
The show snmp csm communities command displays information about the configured SNMP communities.
The show snmp notification log details command displays detailed information about logged SNMP notifications.
The show snmp notification log info command displays summary information about logged SNMP notifications.
The monitor snmp notification log info command displays summary information about logged SNMP notifications.
The dump snmp command generates a sequence of scli commands which can be used to restore the engine configuration.
The sonet scli mode is based on the SONET-MIB as published in RFC 2558. It provides commands to manage Synchronous Optical Network/Synchronous Digital Hierarchy (SONET/SDH) interfaces.
The show sonet media command displays information about the configuration of SONET/SDH interfaces. The command outputs a table which has the following columns:
INTERFACE network interface number
SIGNAL type of the signal (SONET/SDH)
CODING line coding (B3ZS, CMI, NRZ, RZ)
LINE optical or electrical line type
DESCRIPTION description of the network interface
The show sonet section stats command displays statistics about SONET/SDH section errors. The command outputs a table which has the following columns:
INTERFACE network interface number
INTERVAL measurement interval
ES errored seconds
SES severely errored seconds
SEFS severely errored framing seconds
CV coding violations
LOSS flags indicating loss of signal/frame
DESCRIPTION description of the network interface
The show sonet section history command displays 15 minute history statistics about SONET/SDH section errors. The command outputs a table which has the following columns:
INTERFACE network interface number
INTERVAL measurement interval start offset
ES errored seconds
SES severely errored seconds
SEFS severely errored framing seconds
CV coding violations
DESCRIPTION description of the network interface
The monitor sonet section stats command shows the same information as the show sonet section stats command. The information is updated periodically.
The system scli mode is primarily based on the SNMPv2-MIB as published in RFC 1907 and the HOST-RESOURCES-MIB as publisched in RFC 2790. It can be used to browse and configure system parameters and characteristics.
The set system contact command configures the system contact information. The <string> argument should include information on how to contact a person who is responsible for this system.
The set system name command configures the name of the system. By convention, this is the fully-qualified domain name.
The set system location command configures the physical location of the system.
The show system info command shows general information about the system.
The show system devices command shows a list of system devices. The command generates a table with the following columns:
INDEX device number
STATUS current status of the device
DESCRIPTION description of the device
The show system storage command displays information about the logical areas attached in the system. The command generates a table with the following columns:
INDEX logical storage area number
DESCRIPTION description of the storage area
TYPE logical storage area type
SIZE total size of the storage area
USED amount of storage in use
FREE amount of storage available
USE% used storage in percent
The show system mounts command shows the list of filesystems mounted on the system. The command generates a table with the following columns:
INDEX filesystem identification number
LOCAL local root path name of the filesystem
REMOTE remote server and root path name (if any)
TYPE filesytem type (if known)
OPTIONS access mode (ro/rw) and boot flag
The show system processes command display information about the processes currently running on the system. The regular expression <regexp> is matched against the command executed by the process to select the processes of interest. The command generates a table with the following columns:
PID process identification number
S status of the process (see below)
T type of the process (see below)
MEMORY memory used by the process
TIME CPU time used by the process
COMMAND command executed by the process
The process status values are C=running, R=runnable, S=not runnable, and Z=invalid. The process types values are ?=unknown, O=operating system, D=device driver, and A=application.
The show system software command display information about the software installed on the system. The regular expression <regexp> is matched against the software name to select the software of interest. The command generates a table with the following columns:
SID software identification number
T type of the software (see below)
DATE software installation date
NAME software name
The software type values are ?=unknown, O=operating system, D=device driver, and A=application.
The monitor system storage command shows the same information as the show system storage command. The information is updated periodically.
The monitor system processes command show the same information as the show system processes command. The information is updated periodically.
The check system contact command xxx.
The check system storage command checks xxx.
The check system process command checks xxx.
The dump system command generates a sequence of scli commands which can be used to restore the system configuration.
The scli tcp mode is based on the TCP-MIB as published in RFC 2012. It provides commands to browse information specific to the TCP transport protocol.
The show tcp info command displays parameters of the TCP protocol engine.
The show tcp listener command displays the listening TCP endpoints. The command generates a table with the following columns:
LOCAL local TCP endpoint
STATE transmission control block state (listen)
The show tcp connections command displays the connected TCP endpoints including the current state of the connection as seen by the remote SNMP agent. The command generates a table with the following columns:
LOCAL local TCP endpoint
REMOTE remote TCP endpoint
STATE transmission control block state
The transmission control block state is either closed, synSent, synReceived, established, finWait1, finWait2, closeWait, lastAck, closing, or timeWait.
The show tcp states command displays the distribution of TCP transmission control block states together with a list of known port names in each state. The command generates a table with the following columns:
COUNT number of transmission control blocks per state
STATE transmission control block state
PORTS well-known ports associated with the state
The command uses some heuristics to identify the interesting port numbers. First, all local port numbers are considered where the local port number matches one of the listening port numbers. From the remaining connections, all local port numbers are considered with a well known name. From the remaining connections, all remote port numbers are considered with a well known name. All remaining connections are aggregated under the pseudo name - (hyphen). Unspecified port numbers are show using the pseudo name * (star).
The monitor tcp connections command displays the connected TCP endpoints including the current state of the connection as seen by the remote SNMP agent. The information is updated periodically.
The monitor tcp states command displays the distribution of TCP connection states. The information is updated periodically.
The scli sflow mode is based on the SFLOW-MIB as published in RFC 3176 and the SFLOW5-MIB published on the slow.org web site. It provides commands to browse information specific to sflow probes.
The show sflow info command displays information about an sflow implementation.
The show sflow receiver command displays information about sflow receivers.
The scli udp mode is based on the UDP-MIB as published in RFC 2013. It provides commands to browse information specific to the UDP transport protocol.
The show udp listener command displays the listening UDP endpoints.
The show udp statistics about datagrams received or sent.
Large numbers are usually displayed with a scaling factor (k=10^3, m=10^6, g=10^9, t=10^12, p=10^15, K=2^10, M=2^20, G=2^30, T=2^40m, P=2^50).
Aliases are not expanded when the scli interpreter is running in non-interactive mode.
<https://cnds.eecs.jacobs-university.de/svn/schoenw/src/scli/>