netplan
Section: (5)
Updated:
Page Index
NAME
netplan - YAML network configuration abstraction for various backends
SYNOPSIS
netplan [ COMMAND | help ]
COMMANDS
See netplan help for a list of available commands on this
system.
DESCRIPTION
Introduction
Distribution installers, cloud instantiation, image builds for
particular devices, or any other way to deploy an operating system put
its desired network configuration into YAML configuration file(s).
During early boot, the netplan "network renderer" runs which
reads /{lib,etc,run}/netplan/*.yaml and writes configuration to
/run to hand off control of devices to the specified networking
daemon.
- •
-
Configured devices get handled by systemd-networkd by default, unless
explicitly marked as managed by a specific renderer (NetworkManager)
- •
-
Devices not covered by the network config do not get touched at all.
- •
-
Usable in initramfs (few dependencies and fast)
- •
-
No persistent generated config, only original YAML config
- •
-
Parser supports multiple config files to allow applications like libvirt
or lxd to package up expected network config (virbr0,
lxdbr0), or to change the global default policy to use
NetworkManager for everything.
- •
-
Retains the flexibility to change backends/policy later or adjust to
removing NetworkManager, as generated configuration is ephemeral.
General structure
netplan's configuration files use the
YAML (http://yaml.org/spec/1.1/current.html) format.
All /{lib,etc,run}/netplan/*.yaml are considered.
Lexicographically later files (regardless of in which directory they
are) amend (new mapping keys) or override (same mapping keys) previous
ones.
A file in /run/netplan completely shadows a file with same name
in /etc/netplan, and a file in either of those directories
shadows a file with the same name in /lib/netplan.
The top-level node in a netplan configuration file is a
network: mapping that contains version: 2 (the YAML
currently being used by curtin, MaaS, etc.
is version 1), and then device definitions grouped by their type, such
as ethernets:, wifis:, or bridges:.
These are the types that our renderer can understand and are supported
by our backends.
Each type block contains device definitions as a map where the keys
(called "configuration IDs") are defined as below.
Device configuration IDs
The key names below the per-device-type definition maps (like
ethernets:) are called "ID"s.
They must be unique throughout the entire set of configuration files.
Their primary purpose is to serve as anchor names for composite devices,
for example to enumerate the members of a bridge that is currently being
defined.
There are two physically/structurally different classes of device
definitions, and the ID field has a different interpretation for each:
- Physical devices
-
(Examples: ethernet, wifi) These can dynamically come and go between
reboots and even during runtime (hotplugging).
In the generic case, they can be selected by match: rules on
desired properties, such as name/name pattern, MAC address, driver, or
device paths.
In general these will match any number of devices (unless they refer to
properties which are unique such as the full path or MAC address), so
without further knowledge about the hardware these will always be
considered as a group.
-
It is valid to specify no match rules at all, in which case the ID field
is simply the interface name to be matched.
This is mostly useful if you want to keep simple cases simple, and it's
how network device configuration has been done for a long time.
If there are match: rules, then the ID field is a purely opaque
name which is only being used for references from definitions of
compound devices in the config.
- Virtual devices
-
(Examples: veth, bridge, bond) These are fully under the control of the
config file(s) and the network stack.
I.
e.
these devices are being created instead of matched.
Thus match: and set-name: are not applicable for
these, and the ID field is the name of the created virtual device.
-
Common properties for physical device types
- match (mapping)
-
This selects a subset of available physical devices by various hardware
properties.
The following configuration will then apply to all matching devices, as
soon as they appear.
All specified properties must match.
-
- name (scalar)
-
Current interface name.
Globs are supported, and the primary use case for matching on names, as
selecting one fixed name can be more easily achieved with having no
match: at all and just using the ID (see above).
Note that currently only networkd supports globbing, NetworkManager does
not.
-
- macaddress (scalar)
-
Device's MAC address in the form "XX:XX:XX:XX:XX:XX".
Globs are not allowed.
-
- driver (scalar)
-
Kernel driver name, corresponding to the DRIVER udev property.
Globs are supported.
Matching on driver is only supported with networkd.
-
Examples:
- •
-
all cards on second PCI bus:
-
-
match:
name: enp2*
- •
-
fixed MAC address:
-
-
match:
macaddress: 11:22:33:AA:BB:FF
- •
-
first card of driver ixgbe:
-
-
match:
driver: ixgbe
name: en*s0
- set-name (scalar)
-
When matching on unique properties such as path or MAC, or with
additional assumptions such as "there will only ever be one wifi
device", match rules can be written so that they only match one
device.
Then this property can be used to give that device a more
specific/desirable/nicer name than the default from udev's ifnames.
Any additional device that satisfies the match rules will then fail to
get renamed and keep the original kernel name (and dmesg will show an
error).
-
- wakeonlan (bool)
-
Enable wake on LAN.
Off by default.
-
Common properties for all device types
- renderer (scalar)
-
Use the given networking backend for this definition.
Currently supported are networkd and NetworkManager.
This property can be specified globally in networks:, for a
device type (in e.
g.
ethernets:) or for a particular device definition.
Default is networkd.
-
- dhcp4 (bool)
-
Enable DHCP for IPv4.
Off by default.
-
- dhcp6 (bool)
-
Enable DHCP for IPv6.
Off by default.
This covers both stateless DHCP - where the DHCP server supplies
information like DNS nameservers but not the IP address - and stateful
DHCP, where the server provides both the address and the other
information.
-
If you are in an IPv6-only environment with completely stateless
autoconfiguration (SLAAC with RDNSS), this option can be set to cause
the interface to be brought up.
(Setting accept-ra alone is not sufficient.) Autoconfiguration will
still honour the contents of the router advertisement and only use DHCP
if requested in the RA.
Note that rdnssd(8) is required to use RDNSS with
networkd.
No extra software is required for NetworkManager.
- ipv6-privacy (bool)
-
Enable IPv6 Privacy Extensions (RFC 4941) for the specified interface,
and prefer temporary addresses.
Defaults to false - no privacy extensions.
There is currently no way to have a private address but prefer the
public address.
-
- link-local (sequence of scalars)
-
Configure the link-local addresses to bring up.
Valid options are `ipv4' and `ipv6', which respectively allow enabling
IPv4 and IPv6 link local addressing.
If this field is not defined, the default is to enable only IPv6
link-local addresses.
If the field is defined but configured as an empty set, IPv6 link-local
addresses are disabled as well as IPv4 link- local addresses.
-
This feature enables or disables link-local addresses for a protocol,
but the actual implementation differs per backend.
On networkd, this directly changes the behavior and may add an extra
address on an interface.
When using the NetworkManager backend, enabling link-local has no
effect if the interface also has DHCP enabled.
Example to enable only IPv4 link-local:
link-local: [ ipv4 ] Example to enable all link-local
addresses: link-local: [ ipv4, ipv6 ] Example to disable
all link-local addresses: link-local: [ ]
- critical (bool)
-
(networkd backend only) Designate the connection as "critical to the
system", meaning that special care will be taken by
systemd-networkd to not release the IP from DHCP when the daemon is
restarted.
-
- dhcp-identifier (scalar)
-
When set to `mac'; pass that setting over to systemd-networkd to use
the device's MAC address as a unique identifier rather than a
RFC4361-compliant Client ID.
This has no effect when NetworkManager is used as a renderer.
-
- dhcp4-overrides (mapping)
-
(networkd backend only) Overrides default DHCP behavior; see the
DHCP Overrides section below.
-
- dhcp6-overrides (mapping)
-
(networkd backend only) Overrides default DHCP behavior; see the
DHCP Overrides section below.
-
- accept-ra (bool)
-
Accept Router Advertisement that would have the kernel configure IPv6 by
itself.
When enabled, accept Router Advertisements.
When disabled, do not respond to Router Advertisements.
If unset use the host kernel default setting.
-
- addresses (sequence of scalars)
-
Add static addresses to the interface in addition to the ones received
through DHCP or RA.
Each sequence entry is in CIDR notation, i.
e.
of the form addr/prefixlen.
addr is an IPv4 or IPv6 address as recognized by
inet_pton(3) and prefixlen the number of
bits of the subnet.
-
For virtual devices (bridges, bonds, vlan) if there is no address
configured and DHCP is disabled, the interface may still be brought
online, but will not be addressable from the network.
Example: addresses: [192.168.14.2/24, "2001:1::1/64"]
- gateway4, gateway6 (scalar)
-
Set default gateway for IPv4/6, for manual address configuration.
This requires setting addresses too.
Gateway IPs must be in a form recognized by
inet_pton(3).
-
Example for IPv4: gateway4: 172.16.0.1 Example for IPv6:
gateway6: "2001:4::1"
- nameservers (mapping)
-
Set DNS servers and search domains, for manual address configuration.
There are two supported fields: addresses: is a list of IPv4 or
IPv6 addresses similar to gateway*, and search: is a
list of search domains.
-
Example:
-
ethernets:
id0:
[...]
nameservers:
search: [lab, home]
addresses: [8.8.8.8, "FEDC::1"]
- macaddress (scalar)
-
Set the device's MAC address.
The MAC address must be in the form "XX:XX:XX:XX:XX:XX".
-
Note: This will not work reliably for devices matched by name
only and rendered by networkd, due to interactions with device renaming
in udev.
Match devices by MAC when setting MAC addresses.
Example:
-
ethernets:
id0:
match:
macaddress: 52:54:00:6b:3c:58
[...]
macaddress: 52:54:00:6b:3c:59
- mtu (scalar)
-
Set the Maximum Transmission Unit for the interface.
The default is 1500.
Valid values depend on your network interface.
-
Note: This will not work reliably for devices matched by name
only and rendered by networkd, due to interactions with device renaming
in udev.
Match devices by MAC when setting MTU.
- optional (bool)
-
An optional device is not required for booting.
Normally, networkd will wait some time for device to become configured
before proceeding with booting.
However, if a device is marked as optional, networkd will not wait for
it.
This is only supported by networkd, and the default is false.
-
Example:
-
ethernets:
eth7:
# this is plugged into a test network that is often
# down - don't wait for it to come up during boot.
dhcp4: true
optional: true
- optional-addresses (sequence of scalars)
-
Specify types of addresses that are not required for a device to be
considered online.
This changes the behavior of backends at boot time to avoid waiting for
addresses that are marked optional, and thus consider the interface as
"usable" sooner.
This does not disable these addresses, which will be brought up anyway.
-
Example:
-
ethernets:
eth7:
dhcp4: true
dhcp6: true
optional-addresses: [ ipv4-ll, dhcp6 ]
- routes (mapping)
-
Configure static routing for the device; see the Routing
section below.
-
- routing-policy (mapping)
-
Configure policy routing for the device; see the Routing
section below.
-
DHCP Overrides
Several DHCP behavior overrides are available.
Most currently only have any effect when using the networkd
backend, with the exception of use-routes and
route-metric.
Overrides only have an effect if the corresponding dhcp4 or
dhcp6 is set to true.
If both dhcp4 and dhcp6 are true, the
networkd backend requires that dhcp4-overrides and
dhcp6-overrides contain the same keys and values.
If the values do not match, an error will be shown and the network
configuration will not be applied.
When using the NetworkManager backend, different values may be specified
for dhcp4-overrides and dhcp6-overrides, and will be
applied to the DHCP client processes as specified in the netplan YAML.
: The dhcp4-overrides and dhcp6-overrides mappings
override the default DHCP behavior.
-
``use-dns`` (bool)
: Default: ``true``. When ``true``, the DNS servers received from the
DHCP server will be used and take precedence over any statically
configured ones. Currently only has an effect on the ``networkd``
backend.
``use-ntp`` (bool)
: Default: ``true``. When ``true``, the NTP servers received from the
DHCP server will be used by systemd-timesyncd and take precedence
over any statically configured ones. Currently only has an effect on
the ``networkd`` backend.
``send-hostname`` (bool)
: Default: ``true``. When ``true``, the machine's hostname will be sent
to the DHCP server. Currently only has an effect on the ``networkd``
backend.
``use-hostname`` (bool)
: Default: ``true``. When ``true``, the hostname received from the DHCP
server will be set as the transient hostname of the system. Currently
only has an effect on the ``networkd`` backend.
``use-mtu`` (bool)
: Default: ``true``. When ``true``, the MTU received from the DHCP
server will be set as the MTU of the network interface. When ``false``,
the MTU advertised by the DHCP server will be ignored. Currently only
has an effect on the ``networkd`` backend.
``hostname`` (scalar)
: Use this value for the hostname which is sent to the DHCP server,
instead of machine's hostname. Currently only has an effect on the
``networkd`` backend.
``use-routes`` (bool)
: Default: ``true``. When ``true``, the routes received from the DHCP
server will be installed in the routing table normally. When set to
``false``, routes from the DHCP server will be ignored: in this case,
the user is responsible for adding static routes if necessary for
correct network operation. This allows users to avoid installing a
default gateway for interfaces configured via DHCP. Available for
both the ``networkd`` and ``NetworkManager`` backends.
``route-metric`` (scalar)
: Use this value for default metric for automatically-added routes.
Use this to prioritize routes for devices by setting a higher metric
on a preferred interface. Available for both the ``networkd`` and
``NetworkManager`` backends.
Routing
Complex routing is possible with netplan.
Standard static routes as well as policy routing using routing tables
are supported via the networkd backend.
These options are available for all types of interfaces.
- routes (mapping)
-
The routes block defines standard static routes for an
interface.
At least to and via must be specified.
-
For from, to, and via, both IPv4 and IPv6
addresses are recognized, and must be in the form
addr/prefixlen or addr.
- from (scalar)
-
Set a source IP address for traffic going through the route.
-
- to (scalar)
-
Destination address for the route.
-
- via (scalar)
-
Address to the gateway to use for this route.
-
- on-link (bool)
-
When set to "true", specifies that the route is directly
connected to the interface.
-
- metric (scalar)
-
The relative priority of the route.
Must be a positive integer value.
-
- type (scalar)
-
The type of route.
Valid options are "unicast" (default), "unreachable",
"blackhole" or "prohibit".
-
- scope (scalar)
-
The route scope, how wide-ranging it is to the network.
Possible values are "global", "link", or "host".
-
- table (scalar)
-
The table number to use for the route.
In some scenarios, it may be useful to set routes in a separate routing
table.
It may also be used to refer to routing policy rules which also accept a
table parameter.
Allowed values are positive integers starting from 1.
Some values are already in use to refer to specific routing tables: see
/etc/iproute2/rt_tables.
-
- routing-policy (mapping)
-
The routing-policy block defines extra routing policy for a
network, where traffic may be handled specially based on the source IP,
firewall marking, etc.
-
For from, to, both IPv4 and IPv6 addresses are
recognized, and must be in the form addr/prefixlen or
addr.
- from (scalar)
-
Set a source IP address to match traffic for this policy rule.
-
- to (scalar)
-
Match on traffic going to the specified destination.
-
- table (scalar)
-
The table number to match for the route.
In some scenarios, it may be useful to set routes in a separate routing
table.
It may also be used to refer to routes which also accept a
table parameter.
Allowed values are positive integers starting from 1.
Some values are already in use to refer to specific routing tables: see
/etc/iproute2/rt_tables.
-
- priority (scalar)
-
Specify a priority for the routing policy rule, to influence the order
in which routing rules are processed.
A higher number means lower priority: rules are processed in order by
increasing priority number.
-
- mark (scalar)
-
Have this routing policy rule match on traffic that has been marked by
the iptables firewall with this value.
Allowed values are positive integers starting from 1.
-
- type-of-service (scalar)
-
Match this policy rule based on the type of service number applied to
the traffic.
-
Authentication
Netplan supports advanced authentication settings for ethernet and wifi
interfaces, as well as individual wifi networks, by means of the
auth block.
- auth (mapping)
-
Specifies authentication settings for a device of type
ethernets:, or an access-points: entry on a
wifis: device.
-
The auth block supports the following properties:
- key-management (scalar)
-
The supported key management modes are none (no key
management); psk (WPA with pre-shared key, common for home
wifi); eap (WPA with EAP, common for enterprise wifi); and
802.1x (used primarily for wired Ethernet connections).
-
- password (scalar)
-
The password string for EAP, or the pre-shared key for WPA-PSK.
-
The following properties can be used if key-management is
eap or 802.1x:
- method (scalar)
-
The EAP method to use.
The supported EAP methods are tls (TLS), peap
(Protected EAP), and ttls (Tunneled TLS).
-
- identity (scalar)
-
The identity to use for EAP.
-
- anonymous-identity (scalar)
-
The identity to pass over the unencrypted channel if the chosen EAP
method supports passing a different tunnelled identity.
-
- ca-certificate (scalar)
-
Path to a file with one or more trusted certificate authority (CA)
certificates.
-
- client-certificate (scalar)
-
Path to a file containing the certificate to be used by the client
during authentication.
-
- client-key (scalar)
-
Path to a file containing the private key corresponding to
client-certificate.
-
- client-key-password (scalar)
-
Password to use to decrypt the private key specified in
client-key if it is encrypted.
-
Properties for device type ethernets:
Ethernet device definitions do not support any specific properties
beyond the common ones described above.
Properties for device type wifis:
Note that systemd-networkd does not natively support wifi, so
you need wpasupplicant installed if you let the networkd
renderer handle wifi.
- access-points (mapping)
-
This provides pre-configured connections to NetworkManager.
Note that users can of course select other access points/SSIDs.
The keys of the mapping are the SSIDs, and the values are mappings with
the following supported properties:
-
- password (scalar)
-
Enable WPA2 authentication and set the passphrase for it.
If neither this nor an auth block are given, the network is
assumed to be open.
The setting
-
-
password: "S3kr1t"
is equivalent to
-
auth:
key-management: psk
password: "S3kr1t"
- mode (scalar)
-
Possible access point modes are infrastructure (the default),
ap (create an access point to which other devices can connect),
and adhoc (peer to peer networks without a central access
point).
ap is only supported with NetworkManager.
-
Properties for device type bridges:
- interfaces (sequence of scalars)
-
All devices matching this ID list will be added to the bridge.
This may be an empty list, in which case the bridge will be brought
online with no member interfaces.
-
Example:
-
ethernets:
switchports:
match: {name: "enp2*"}
[...]
bridges:
br0:
interfaces: [switchports]
- parameters (mapping)
-
Customization parameters for special bridging options.
Time intervals may need to be expressed as a number of seconds or
milliseconds: the default value type is specified below.
If necessary, time intervals can be qualified using a time suffix (such
as "s" for seconds, "ms" for milliseconds) to allow for
more control over its behavior.
-
- ageing-time (scalar)
-
Set the period of time to keep a MAC address in the forwarding database
after a packet is received.
This maps to the AgeingTimeSec= property when the networkd renderer is
used.
If no time suffix is specified, the value will be interpreted as
seconds.
-
- priority (scalar)
-
Set the priority value for the bridge.
This value should be a number between 0 and 65535.
Lower values mean higher priority.
The bridge with the higher priority will be elected as the root bridge.
-
- port-priority (scalar)
-
Set the port priority to .
The priority value is a number between 0 and 63.
This metric is used in the designated port and root port selection
algorithms.
-
- forward-delay (scalar)
-
Specify the period of time the bridge will remain in Listening and
Learning states before getting to the Forwarding state.
This field maps to the ForwardDelaySec= property for the networkd
renderer.
If no time suffix is specified, the value will be interpreted as
seconds.
-
- hello-time (scalar)
-
Specify the interval between two hello packets being sent out from the
root and designated bridges.
Hello packets communicate information about the network topology.
When the networkd renderer is used, this maps to the HelloTimeSec=
property.
If no time suffix is specified, the value will be interpreted as
seconds.
-
- max-age (scalar)
-
Set the maximum age of a hello packet.
If the last hello packet is older than that value, the bridge will
attempt to become the root bridge.
This maps to the MaxAgeSec= property when the networkd renderer is used.
If no time suffix is specified, the value will be interpreted as
seconds.
-
- path-cost (scalar)
-
Set the cost of a path on the bridge.
Faster interfaces should have a lower cost.
This allows a finer control on the network topology so that the fastest
paths are available whenever possible.
-
- stp (bool)
-
Define whether the bridge should use Spanning Tree Protocol.
The default value is "true", which means that Spanning Tree
should be used.
-
Properties for device type bonds:
- interfaces (sequence of scalars)
-
All devices matching this ID list will be added to the bond.
-
Example:
-
ethernets:
switchports:
match: {name: "enp2*"}
[...]
bonds:
bond0:
interfaces: [switchports]
- parameters (mapping)
-
Customization parameters for special bonding options.
Time intervals may need to be expressed as a number of seconds or
milliseconds: the default value type is specified below.
If necessary, time intervals can be qualified using a time suffix (such
as "s" for seconds, "ms" for milliseconds) to allow for
more control over its behavior.
-
- mode (scalar)
-
Set the bonding mode used for the interfaces.
The default is balance-rr (round robin).
Possible values are balance-rr, active-backup,
balance-xor, broadcast, 802.3ad,
balance-tlb, and balance-alb.
-
- lacp-rate (scalar)
-
Set the rate at which LACPDUs are transmitted.
This is only useful in 802.3ad mode.
Possible values are slow (30 seconds, default), and
fast (every second).
-
- mii-monitor-interval (scalar)
-
Specifies the interval for MII monitoring (verifying if an interface of
the bond has carrier).
The default is 0; which disables MII monitoring.
This is equivalent to the MIIMonitorSec= field for the networkd backend.
If no time suffix is specified, the value will be interpreted as
milliseconds.
-
- min-links (scalar)
-
The minimum number of links up in a bond to consider the bond interface
to be up.
-
- transmit-hash-policy (scalar)
-
Specifies the transmit hash policy for the selection of slaves.
This is only useful in balance-xor, 802.3ad and balance-tlb modes.
Possible values are layer2, layer3+4,
layer2+3, encap2+3, and encap3+4.
-
- ad-select (scalar)
-
Set the aggregation selection mode.
Possible values are stable, bandwidth, and
count.
This option is only used in 802.3ad mode.
-
- all-slaves-active (bool)
-
If the bond should drop duplicate frames received on inactive ports, set
this option to false.
If they should be delivered, set this option to true.
The default value is false, and is the desirable behavior in most
situations.
-
- arp-interval (scalar)
-
Set the interval value for how frequently ARP link monitoring should
happen.
The default value is 0, which disables ARP monitoring.
For the networkd backend, this maps to the ARPIntervalSec= property.
If no time suffix is specified, the value will be interpreted as
milliseconds.
-
- arp-ip-targets (sequence of scalars)
-
IPs of other hosts on the link which should be sent ARP requests in
order to validate that a slave is up.
This option is only used when arp-interval is set to a value
other than 0.
At least one IP address must be given for ARP link monitoring to
function.
Only IPv4 addresses are supported.
You can specify up to 16 IP addresses.
The default value is an empty list.
-
- arp-validate (scalar)
-
Configure how ARP replies are to be validated when using ARP link
monitoring.
Possible values are none, active, backup, and
all.
-
- arp-all-targets (scalar)
-
Specify whether to use any ARP IP target being up as sufficient for a
slave to be considered up; or if all the targets must be up.
This is only used for active-backup mode when
arp-validate is enabled.
Possible values are any and all.
-
- up-delay (scalar)
-
Specify the delay before enabling a link once the link is physically up.
The default value is 0.
This maps to the UpDelaySec= property for the networkd renderer.
If no time suffix is specified, the value will be interpreted as
milliseconds.
-
- down-delay (scalar)
-
Specify the delay before disabling a link once the link has been lost.
The default value is 0.
This maps to the DownDelaySec= property for the networkd renderer.
If no time suffix is specified, the value will be interpreted as
milliseconds.
-
- fail-over-mac-policy (scalar)
-
Set whether to set all slaves to the same MAC address when adding them
to the bond, or how else the system should handle MAC addresses.
The possible values are none, active, and
follow.
-
- gratuitous-arp (scalar)
-
Specify how many ARP packets to send after failover.
Once a link is up on a new slave, a notification is sent and possibly
repeated if this value is set to a number greater than 1.
The default value is 1 and valid values are between 1
and 255.
This only affects active-backup mode.
-
For historical reasons, the misspelling gratuitious-arp is
also accepted and has the same function.
- packets-per-slave (scalar)
-
In balance-rr mode, specifies the number of packets to
transmit on a slave before switching to the next.
When this value is set to 0, slaves are chosen at random.
Allowable values are between 0 and 65535.
The default value is 1.
This setting is only used in balance-rr mode.
-
- primary-reselect-policy (scalar)
-
Set the reselection policy for the primary slave.
On failure of the active slave, the system will use this policy to
decide how the new active slave will be chosen and how recovery will be
handled.
The possible values are always, better, and
failure.
-
- resend-igmp (scalar)
-
In modes balance-rr, active-backup,
balance-tlb and balance-alb, a failover can switch
IGMP traffic from one slave to another.
-
This parameter specifies how many IGMP membership reports are issued on
a failover event.
Values range from 0 to 255.
0 disables sending membership reports.
Otherwise, the first membership report is sent on failover and
subsequent reports are sent at 200ms intervals.
- learn-packet-interval (scalar)
-
Specify the interval between sending learning packets to each slave.
The value range is between 1 and 0x7fffffff.
The default value is 1.
This option only affects balance-tlb and balance-alb
modes.
Using the networkd renderer, this field maps to the
LearnPacketIntervalSec= property.
If no time suffix is specified, the value will be interpreted as
seconds.
-
- primary (scalar)
-
Specify a device to be used as a primary slave, or preferred device to
use as a slave for the bond (ie.
the preferred device to send data through), whenever it is available.
This only affects active-backup, balance-alb, and
balance-tlb modes.
-
Properties for device type tunnels:
Tunnels allow traffic to pass as if it was between systems on the same
local network, although systems may be far from each other but reachable
via the Internet.
They may be used to support IPv6 traffic on a network where the ISP does
not provide the service, or to extend and "connect" separate
local networks.
Please see https://en.wikipedia.org/wiki/Tunneling_protocol for more
general information about tunnels.
- mode (scalar)
-
Defines the tunnel mode.
Valid options are sit, gre, ip6gre,
ipip, ipip6, ip6ip6, vti, and
vti6.
Additionally, the networkd backend also supports
gretap and ip6gretap modes.
In addition, the NetworkManager backend supports
isatap tunnels.
-
- local (scalar)
-
Defines the address of the local endpoint of the tunnel.
-
- remote (scalar)
-
Defines the address of the remote endpoint of the tunnel.
-
- key (scalar or mapping)
-
Define keys to use for the tunnel.
The key can be a number or a dotted quad (an IPv4 address).
It is used for identification of IP transforms.
This is only required for vti and vti6 when using the
networkd backend, and for gre or ip6gre tunnels when
using the NetworkManager backend.
-
This field may be used as a scalar (meaning that a single key is
specified and to be used for both input and output key), or as a
mapping, where you can then further specify input and
output.
- input (scalar)
-
The input key for the tunnel
-
- output (scalar)
-
The output key for the tunnel
-
Examples:
-
tunnels:
tun0:
mode: gre
local: ...
remote: ...
keys:
input: 1234
output: 5678
tunnels:
tun0:
mode: vti6
local: ...
remote: ...
key: 59568549
- keys (scalar or mapping)
-
Alternate name for the key field.
See above.
-
Properties for device type vlans:
- id (scalar)
-
VLAN ID, a number between 0 and 4094.
-
- link (scalar)
-
netplan ID of the underlying device definition on which this VLAN gets
created.
-
Example:
-
ethernets:
eno1: {...}
vlans:
en-intra:
id: 1
link: eno1
dhcp4: yes
en-vpn:
id: 2
link: eno1
addresses: ...
Examples
Configure an ethernet device with networkd, identified by its name, and
enable DHCP:
-
network:
version: 2
ethernets:
eno1:
dhcp4: true
This is an example of a static-configured interface with multiple IPv4
addresses and multiple gateways with networkd, with equal route metric
levels, and static DNS nameservers (Google DNS for this example):
-
network:
version: 2
renderer: networkd
ethernets:
eno1:
addresses:
- 10.0.0.10/24
- 11.0.0.11/24
nameservers:
addresses:
- 8.8.8.8
- 8.8.4.4
routes:
- to: 0.0.0.0/0
via: 10.0.0.1
metric: 100
- to: 0.0.0.0/0
via: 11.0.0.1
metric: 100
This is a complex example which shows most available features:
-
network:
version: 2
# if specified, can only realistically have that value, as networkd cannot
# render wifi/3G.
renderer: NetworkManager
ethernets:
# opaque ID for physical interfaces, only referred to by other stanzas
id0:
match:
macaddress: 00:11:22:33:44:55
wakeonlan: true
dhcp4: true
addresses:
- 192.168.14.2/24
- 192.168.14.3/24
- "2001:1::1/64"
gateway4: 192.168.14.1
gateway6: "2001:1::2"
nameservers:
search: [foo.local, bar.local]
addresses: [8.8.8.8]
routes:
- to: 0.0.0.0/0
via: 11.0.0.1
table: 70
on-link: true
metric: 3
routing-policy:
- to: 10.0.0.0/8
from: 192.168.14.2/24
table: 70
priority: 100
- to: 20.0.0.0/8
from: 192.168.14.3/24
table: 70
priority: 50
# only networkd can render on-link routes and routing policies
renderer: networkd
lom:
match:
driver: ixgbe
# you are responsible for setting tight enough match rules
# that only match one device if you use set-name
set-name: lom1
dhcp6: true
switchports:
# all cards on second PCI bus unconfigured by
# themselves, will be added to br0 below
# note: globbing is not supported by NetworkManager
match:
name: enp2*
mtu: 1280
wifis:
all-wlans:
# useful on a system where you know there is
# only ever going to be one device
match: {}
access-points:
"Joe's home":
# mode defaults to "infrastructure" (client)
password: "s3kr1t"
# this creates an AP on wlp1s0 using hostapd
# no match rules, thus the ID is the interface name
wlp1s0:
access-points:
"guest":
mode: ap
# no WPA config implies default of open
bridges:
# the key name is the name for virtual (created) interfaces
# no match: and set-name: allowed
br0:
# IDs of the components; switchports expands into multiple interfaces
interfaces: [wlp1s0, switchports]
dhcp4: true
SEE ALSO
netplan-generate(8), netplan-apply(8),
netplan-try(8), systemd-networkd(8),
NetworkManager(8)
AUTHORS
Mathieu Trudel-Lapierre (<
cyphermox@ubuntu.com>); Martin Pitt (<
martin.pitt@ubuntu.com>).