Some information is not available on older processors.
--add attributes add column with counter having specified 'attributes'. The 'location' attribute is required, all others are optional.
location: {msrDDD | msr0xXXX | /sys/path...}
msrDDD is a decimal offset, eg. msr16
msr0xXXX is a hex offset, eg. msr0x10
/sys/path... is an absolute path to a sysfs attribute
scope: {cpu | core | package}
sample and print the counter for every cpu, core, or package.
default: cpu
size: {u32 | u64 }
MSRs are read as 64-bits, u32 truncates the displayed value to 32-bits.
default: u64
format: {raw | delta | percent}
'raw' shows the MSR contents in hex.
'delta' shows the difference in values during the measurement interval.
'percent' shows the delta as a percentage of the cycles elapsed.
default: delta
name: "name_string"
Any string that does not match a key-word above is used
as the column header.
--cpu cpu-set limit output to system summary plus the specified cpu-set. If cpu-set is the string "core", then the system summary plus the first CPU in each core are printed -- eg. subsequent HT siblings are not printed. Or if cpu-set is the string "package", then the system summary plus the first CPU in each package is printed. Otherwise, the system summary plus the specified set of CPUs are printed. The cpu-set is ordered from low to high, comma delimited with ".." and "-" permitted to denote a range. eg. 1,2,8,14..17,21-44
--hide column do not show the specified built-in columns. May be invoked multiple times, or with a comma-separated list of column names. Use "--hide sysfs" to hide the sysfs statistics columns as a group.
--enable column show the specified built-in columns, which are otherwise disabled, by default. Currently the only built-in counters disabled by default are "usec", "Time_Of_Day_Seconds", "APIC" and "X2APIC". The column name "all" can be used to enable all disabled-by-default built-in counters.
--show column show only the specified built-in columns. May be invoked multiple times, or with a comma-separated list of column names. Use "--show sysfs" to show the sysfs statistics columns as a group.
--Dump displays the raw counter values.
--quiet Do not decode and print the system configuration header information.
--interval seconds overrides the default 5.0 second measurement interval.
--num_iterations num number of the measurement iterations.
--out output_file turbostat output is written to the specified output_file. The file is truncated if it already exists, and it is created if it does not exist.
--help displays usage for the most common parameters.
--Joules displays energy in Joules, rather than dividing Joules by time to print power in Watts.
--list display column header names available for use by --show and --hide, then exit.
--Summary limits output to a 1-line System Summary for each interval.
--TCC temperature sets the Thermal Control Circuit temperature for systems which do not export that value. This is used for making sense of the Digital Thermal Sensor outputs, as they return degrees Celsius below the TCC activation temperature.
--version displays the version.
The command parameter forks command, and upon its exit, displays the statistics gathered since it was forked.
usec For each CPU, the number of microseconds elapsed during counter collection, including thread migration -- if any. This counter is disabled by default, and is enabled with "--enable usec", or --debug. On the summary row, usec refers to the total elapsed time to collect the counters on all cpus. Time_Of_Day_Seconds For each CPU, the gettimeofday(2) value (seconds.subsec since Epoch) when the counters ending the measurement interval were collected. This column is disabled by default, and can be enabled with "--enable Time_Of_Day_Seconds" or "--debug". On the summary row, Time_Of_Day_Seconds refers to the timestamp following collection of counters on the last CPU. Core processor core number. Note that multiple CPUs per core indicate support for Intel(R) Hyper-Threading Technology (HT). CPU Linux CPU (logical processor) number. Yes, it is okay that on many systems the CPUs are not listed in numerical order -- for efficiency reasons, turbostat runs in topology order, so HT siblings appear together. Package processor package number -- not present on systems with a single processor package. Avg_MHz number of cycles executed divided by time elapsed. Note that this includes idle-time when 0 instructions are executed. Busy% percent of the measurement interval that the CPU executes instructions, aka. % of time in "C0" state. Bzy_MHz average clock rate while the CPU was not idle (ie. in "c0" state). TSC_MHz average MHz that the TSC ran during the entire interval. IRQ The number of interrupts serviced by that CPU during the measurement interval. The system total line is the sum of interrupts serviced across all CPUs. turbostat parses /proc/interrupts to generate this summary. SMI The number of System Management Interrupts serviced CPU during the measurement interval. While this counter is actually per-CPU, SMI are triggered on all processors, so the number should be the same for all CPUs. C1, C2, C3... The number times Linux requested the C1, C2, C3 idle state during the measurement interval. The system summary line shows the sum for all CPUs. These are C-state names as exported in /sys/devices/system/cpu/cpu*/cpuidle/state*/name. While their names are generic, their attributes are processor specific. They the system description section of output shows what MWAIT sub-states they are mapped to on each system. C1%, C2%, C3% The residency percentage that Linux requested C1, C2, C3.... The system summary is the average of all CPUs in the system. Note that these are software, reflecting what was requested. The hardware counters reflect what was actually achieved. CPU%c1, CPU%c3, CPU%c6, CPU%c7 show the percentage residency in hardware core idle states. These numbers are from hardware residency counters. CoreTmp Degrees Celsius reported by the per-core Digital Thermal Sensor. PkgTmp Degrees Celsius reported by the per-package Package Thermal Monitor. GFX%rc6 The percentage of time the GPU is in the "render C6" state, rc6, during the measurement interval. From /sys/class/drm/card0/power/rc6_residency_ms. GFXMHz Instantaneous snapshot of what sysfs presents at the end of the measurement interval. From /sys/class/graphics/fb0/device/drm/card0/gt_cur_freq_mhz. Pkg%pc2, Pkg%pc3, Pkg%pc6, Pkg%pc7 percentage residency in hardware package idle states. These numbers are from hardware residency counters. PkgWatt Watts consumed by the whole package. CorWatt Watts consumed by the core part of the package. GFXWatt Watts consumed by the Graphics part of the package -- available only on client processors. RAMWatt Watts consumed by the DRAM DIMMS -- available only on server processors. PKG_% percent of the interval that RAPL throttling was active on the Package. Note that the system summary is the sum of the package throttling time, and thus may be higher than 100% on a multi-package system. Note that the meaning of this field is model specific. For example, some hardware increments this counter when RAPL responds to thermal limits, but does not increment this counter when RAPL responds to power limits. Comparing PkgWatt and PkgTmp to system limits is necessary. RAM_% percent of the interval that RAPL throttling was active on DRAM.
When you are not interested in all that information, and there are several ways to see only what you want. First the "--quiet" option will skip the configuration information, and turbostat will show only the counter columns. Second, you can reduce the columns with the "--hide" and "--show" options. If you use the "--show" option, then turbostat will show only the columns you list. If you use the "--hide" option, turbostat will show all columns, except the ones you list.
To find out what columns are available for --show and --hide, the "--list" option is available. For convenience, the special strings "sysfs" can be used to refer to all of the sysfs C-state counters at once:
sudo ./turbostat --show sysfs --quiet sleep 10
10.003837 sec
C1 C1E C3 C6 C7s C1% C1E% C3% C6% C7s%
4 21 2 2 459 0.14 0.82 0.00 0.00 98.93
1 17 2 2 130 0.00 0.02 0.00 0.00 99.80
0 0 0 0 31 0.00 0.00 0.00 0.00 99.95
2 1 0 0 52 1.14 6.49 0.00 0.00 92.21
1 2 0 0 52 0.00 0.08 0.00 0.00 99.86
0 0 0 0 71 0.00 0.00 0.00 0.00 99.89
0 0 0 0 25 0.00 0.00 0.00 0.00 99.96
0 0 0 0 74 0.00 0.00 0.00 0.00 99.94
0 1 0 0 24 0.00 0.00 0.00 0.00 99.84
[root@hsw]# ./turbostat -o ts.out sleep 10 [root@hsw]#
sudo ./turbostat --quiet --hide sysfs,IRQ,SMI,CoreTmp,PkgTmp,GFX%rc6,GFXMHz,PkgWatt,CorWatt,GFXWatt
Core CPU Avg_MHz Busy% Bzy_MHz TSC_MHz CPU%c1 CPU%c3 CPU%c6 CPU%c7
- - 488 12.52 3900 3498 12.50 0.00 0.00 74.98
0 0 5 0.13 3900 3498 99.87 0.00 0.00 0.00
0 4 3897 99.99 3900 3498 0.01
1 1 0 0.00 3856 3498 0.01 0.00 0.00 99.98
1 5 0 0.00 3861 3498 0.01
2 2 1 0.02 3889 3498 0.03 0.00 0.00 99.95
2 6 0 0.00 3863 3498 0.05
3 3 0 0.01 3869 3498 0.02 0.00 0.00 99.97
3 7 0 0.00 3878 3498 0.03
Core CPU Avg_MHz Busy% Bzy_MHz TSC_MHz CPU%c1 CPU%c3 CPU%c6 CPU%c7
- - 491 12.59 3900 3498 12.42 0.00 0.00 74.99
0 0 27 0.69 3900 3498 99.31 0.00 0.00 0.00
0 4 3898 99.99 3900 3498 0.01
1 1 0 0.00 3883 3498 0.01 0.00 0.00 99.99
1 5 0 0.00 3898 3498 0.01
2 2 0 0.01 3889 3498 0.02 0.00 0.00 99.98
2 6 0 0.00 3889 3498 0.02
3 3 0 0.00 3856 3498 0.01 0.00 0.00 99.99
3 7 0 0.00 3897 3498 0.01
This example also shows the use of the --hide option to skip columns that are not wanted.
Note that cpu4 in this example is 99.99% busy, while the other CPUs are all under 1% busy.
Notice that cpu4's HT sibling is cpu0, which is under 1% busy, but can get into CPU%c1 only,
because its cpu4's activity on shared hardware keeps it from entering a deeper C-state.
By default, turbostat always dumps system configuration information before taking measurements. In the example above, "--quiet" is used to suppress that output. Here is an example of the configuration information:
turbostat version 2017.02.15 - Len Brown <lenb@kernel.org> CPUID(0): GenuineIntel 13 CPUID levels; family:model:stepping 0x6:3c:3 (6:60:3) CPUID(1): SSE3 MONITOR - EIST TM2 TSC MSR ACPI-TM TM CPUID(6): APERF, TURBO, DTS, PTM, No-HWP, No-HWPnotify, No-HWPwindow, No-HWPepp, No-HWPpkg, EPB cpu4: MSR_IA32_MISC_ENABLE: 0x00850089 (TCC EIST No-MWAIT PREFETCH TURBO) CPUID(7): No-SGX cpu4: MSR_MISC_PWR_MGMT: 0x00400000 (ENable-EIST_Coordination DISable-EPB DISable-OOB) RAPL: 3121 sec. Joule Counter Range, at 84 Watts cpu4: MSR_PLATFORM_INFO: 0x80838f3012300 8 * 100.0 = 800.0 MHz max efficiency frequency 35 * 100.0 = 3500.0 MHz base frequency cpu4: MSR_IA32_POWER_CTL: 0x0004005d (C1E auto-promotion: DISabled) cpu4: MSR_TURBO_RATIO_LIMIT: 0x25262727 37 * 100.0 = 3700.0 MHz max turbo 4 active cores 38 * 100.0 = 3800.0 MHz max turbo 3 active cores 39 * 100.0 = 3900.0 MHz max turbo 2 active cores 39 * 100.0 = 3900.0 MHz max turbo 1 active cores cpu4: MSR_CONFIG_TDP_NOMINAL: 0x00000023 (base_ratio=35) cpu4: MSR_CONFIG_TDP_LEVEL_1: 0x00000000 () cpu4: MSR_CONFIG_TDP_LEVEL_2: 0x00000000 () cpu4: MSR_CONFIG_TDP_CONTROL: 0x80000000 ( lock=1) cpu4: MSR_TURBO_ACTIVATION_RATIO: 0x00000000 (MAX_NON_TURBO_RATIO=0 lock=0) cpu4: MSR_PKG_CST_CONFIG_CONTROL: 0x1e000400 (UNdemote-C3, UNdemote-C1, demote-C3, demote-C1, UNlocked: pkg-cstate-limit=0: pc0) cpu4: POLL: CPUIDLE CORE POLL IDLE cpu4: C1: MWAIT 0x00 cpu4: C1E: MWAIT 0x01 cpu4: C3: MWAIT 0x10 cpu4: C6: MWAIT 0x20 cpu4: C7s: MWAIT 0x32 cpu4: MSR_MISC_FEATURE_CONTROL: 0x00000000 (L2-Prefetch L2-Prefetch-pair L1-Prefetch L1-IP-Prefetch) cpu0: MSR_IA32_ENERGY_PERF_BIAS: 0x00000006 (balanced) cpu0: MSR_CORE_PERF_LIMIT_REASONS, 0x31200000 (Active: ) (Logged: Transitions, MultiCoreTurbo, Amps, Auto-HWP, ) cpu0: MSR_GFX_PERF_LIMIT_REASONS, 0x00000000 (Active: ) (Logged: ) cpu0: MSR_RING_PERF_LIMIT_REASONS, 0x0d000000 (Active: ) (Logged: Amps, PkgPwrL1, PkgPwrL2, ) cpu0: MSR_RAPL_POWER_UNIT: 0x000a0e03 (0.125000 Watts, 0.000061 Joules, 0.000977 sec.) cpu0: MSR_PKG_POWER_INFO: 0x000002a0 (84 W TDP, RAPL 0 - 0 W, 0.000000 sec.) cpu0: MSR_PKG_POWER_LIMIT: 0x428348001a82a0 (UNlocked) cpu0: PKG Limit #1: ENabled (84.000000 Watts, 8.000000 sec, clamp DISabled) cpu0: PKG Limit #2: ENabled (105.000000 Watts, 0.002441* sec, clamp DISabled) cpu0: MSR_PP0_POLICY: 0 cpu0: MSR_PP0_POWER_LIMIT: 0x00000000 (UNlocked) cpu0: Cores Limit: DISabled (0.000000 Watts, 0.000977 sec, clamp DISabled) cpu0: MSR_PP1_POLICY: 0 cpu0: MSR_PP1_POWER_LIMIT: 0x00000000 (UNlocked) cpu0: GFX Limit: DISabled (0.000000 Watts, 0.000977 sec, clamp DISabled) cpu0: MSR_IA32_TEMPERATURE_TARGET: 0x00641400 (100 C) cpu0: MSR_IA32_PACKAGE_THERM_STATUS: 0x884c0800 (24 C) cpu0: MSR_IA32_THERM_STATUS: 0x884c0000 (24 C +/- 1) cpu1: MSR_IA32_THERM_STATUS: 0x88510000 (19 C +/- 1) cpu2: MSR_IA32_THERM_STATUS: 0x884e0000 (22 C +/- 1) cpu3: MSR_IA32_THERM_STATUS: 0x88510000 (19 C +/- 1) cpu4: MSR_PKGC3_IRTL: 0x00008842 (valid, 67584 ns) cpu4: MSR_PKGC6_IRTL: 0x00008873 (valid, 117760 ns) cpu4: MSR_PKGC7_IRTL: 0x00008891 (valid, 148480 ns)The max efficiency frequency, a.k.a. Low Frequency Mode, is the frequency available at the minimum package voltage. The TSC frequency is the base frequency of the processor -- this should match the brand string in /proc/cpuinfo. This base frequency should be sustainable on all CPUs indefinitely, given nominal power and cooling. The remaining rows show what maximum turbo frequency is possible depending on the number of idle cores. Note that not all information is available on all processors.
sudo ./turbostat --quiet --cpu 0-3 --show CPU --add msr0x199,u32,raw,PRF_CTRL sleep .1 0.101604 sec CPU PRF_CTRL - 0x00000000 0 0x00000c00 1 0x00000800 2 0x00000a00 3 0x00000800
For interval-mode, turbostat will immediately end the current interval when it sees a newline on standard input. turbostat will then start the next interval. Control-C will be send a SIGINT to turbostat, which will immediately abort the program with no further processing.
SIGINT will interrupt interval-mode. The end-of-interval data will be collected and displayed before turbostat exits.
SIGUSR1 will end current interval, end-of-interval data will be collected and displayed before turbostat starts a new interval.
turbostat must be run as root. Alternatively, non-root users can be enabled to run turbostat this way:
# setcap cap_sys_rawio=ep ./turbostat
# chmod +r /dev/cpu/*/msr
turbostat reads hardware counters, but doesn't write them. So it will not interfere with the OS or other programs, including multiple invocations of itself.
turbostat may work poorly on Linux-2.6.20 through 2.6.29, as acpi-cpufreq periodically cleared the APERF and MPERF MSRs in those kernels.
AVG_MHz = APERF_delta/measurement_interval. This is the actual number of elapsed cycles divided by the entire sample interval -- including idle time. Note that this calculation is resilient to systems lacking a non-stop TSC.
TSC_MHz = TSC_delta/measurement_interval. On a system with an invariant TSC, this value will be constant and will closely match the base frequency value shown in the brand string in /proc/cpuinfo. On a system where the TSC stops in idle, TSC_MHz will drop below the processor's base frequency.
Busy% = MPERF_delta/TSC_delta
Bzy_MHz = TSC_delta/APERF_delta/MPERF_delta/measurement_interval
Note that these calculations depend on TSC_delta, so they are not reliable during intervals when TSC_MHz is not running at the base frequency.
Turbostat data collection is not atomic. Extremely short measurement intervals (much less than 1 second), or system activity that prevents turbostat from being able to run on all CPUS to quickly collect data, will result in inconsistent results.
The APERF, MPERF MSRs are defined to count non-halted cycles. Although it is not guaranteed by the architecture, turbostat assumes that they count at TSC rate, which is true on all processors tested to date.
/dev/cpu/*/msr
Written by Len Brown <len.brown@intel.com>