Section: Linux Programmer's Manual (2)
ioprio_get, ioprio_set - get/set I/O scheduling class and priority
int ioprio_get(int which, int who);
int ioprio_set(int which, int who, int ioprio);
There are no glibc wrappers for these system calls; see NOTES.
system calls get and set the I/O scheduling class and
priority of one or more threads.
arguments identify the thread(s) on which the system
argument determines how
is interpreted, and has one of the following values:
is a process ID or thread ID identifying a single process or thread.
is 0, then operate on the calling thread.
is a process group ID identifying all the members of a process group.
is 0, then operate on the process group of which the caller is a member.
is a user ID identifying all of the processes that
have a matching real UID.
is specified as
and more than one process matches
then the returned priority will be the highest one found among
all of the matching processes.
One priority is said to be
higher than another one if it belongs to a higher priority
is the highest priority class;
is the lowest)
or if it belongs to the same priority class as the other process but
has a higher priority level (a lower priority number means a
higher priority level).
argument given to
is a bit mask that specifies both the scheduling class and the
priority to be assigned to the target process(es).
The following macros are used for assembling and dissecting
- IOPRIO_PRIO_VALUE(class, data)
Given a scheduling
this macro combines the two values to produce an
value, which is returned as the result of the macro.
value), this macro returns its I/O class component, that is,
one of the values
value), this macro returns its priority
See the NOTES section for more
information on scheduling classes and priorities,
as well as the meaning of specifying
I/O priorities are supported for reads and for synchronous
I/O priorities are not supported for asynchronous
writes because they are issued outside the context of the program
dirtying the memory, and thus program-specific priorities do not apply.
value of the process with highest I/O priority of any of the processes
that match the criteria specified in
On error, -1 is returned, and
is set to indicate the error.
On error, -1 is returned, and
is set to indicate the error.
Invalid value for
Refer to the NOTES section for available scheduler
classes and priority levels for
The calling process does not have the privilege needed to assign this
to the specified process(es).
See the NOTES section for more information on required
No process(es) could be found that matched the specification in
These system calls have been available on Linux since
These system calls are Linux-specific.
Glibc does not provide a wrapper for these system calls; call them using
Two or more processes or threads can share an I/O context.
This will be the case when
was called with the
However, by default, the distinct threads of a process will
share the same I/O context.
This means that if you want to change the I/O
priority of all threads in a process, you may need to call
on each of the threads.
The thread ID that you would need for this operation
is the one that is returned by
These system calls have an effect only when used
in conjunction with an I/O scheduler that supports I/O priorities.
As at kernel 2.6.17 the only such scheduler is the Completely Fair Queuing
(CFQ) I/O scheduler.
If no I/O scheduler has been set for a thread,
then by default the I/O priority will follow the CPU nice value
In Linux kernels before version 2.6.24,
once an I/O priority had been set using
there was no way to reset the I/O scheduling behavior to the default.
Since Linux 2.6.24,
as 0 can be used to reset to the default I/O scheduling behavior.
Selecting an I/O scheduler
I/O schedulers are selected on a per-device basis via the special
One can view the current I/O scheduler via the
For example, the following command
displays a list of all schedulers currently loaded in the kernel:
$ cat /sys/block/sda/queue/scheduler
noop anticipatory deadline [cfq]
The scheduler surrounded by brackets is the one actually
in use for the device
in the example).
Setting another scheduler is done by writing the name of the
new scheduler to this file.
For example, the following command will set the
scheduler for the
# echo cfq > /sys/block/sda/queue/scheduler
The Completely Fair Queuing (CFQ) I/O scheduler
Since version 3 (also known as CFQ Time Sliced), CFQ implements
I/O nice levels similar to those
of CPU scheduling.
These nice levels are grouped into three scheduling classes,
each one containing one or more priority levels:
- IOPRIO_CLASS_RT (1)
This is the real-time I/O class.
This scheduling class is given
higher priority than any other class:
processes from this class are
given first access to the disk every time.
Thus, this I/O class needs to be used with some
care: one I/O real-time process can starve the entire system.
Within the real-time class,
there are 8 levels of class data (priority) that determine exactly
how much time this process needs the disk for on each service.
The highest real-time priority level is 0; the lowest is 7.
In the future, this might change to be more directly mappable to
performance, by passing in a desired data rate instead.
- IOPRIO_CLASS_BE (2)
This is the best-effort scheduling class,
which is the default for any process
that hasn't set a specific I/O priority.
The class data (priority) determines how much
I/O bandwidth the process will get.
Best-effort priority levels are analogous to CPU nice values
The priority level determines a priority relative
to other processes in the best-effort scheduling class.
Priority levels range from 0 (highest) to 7 (lowest).
- IOPRIO_CLASS_IDLE (3)
This is the idle scheduling class.
Processes running at this level get I/O
time only when no one else needs the disk.
The idle class has no class data.
Attention is required when assigning this priority class to a process,
since it may become starved if higher priority processes are
constantly accessing the disk.
Refer to the kernel source file
for more information on the CFQ I/O Scheduler and an example program.
Required permissions to set I/O priorities
Permission to change a process's priority is granted or denied based
on two criteria:
- Process ownership
An unprivileged process may set the I/O priority only for a process
whose real UID
matches the real or effective UID of the calling process.
A process which has the
capability can change the priority of any process.
- What is the desired priority
Attempts to set very high priorities
Kernel versions up to 2.6.24 also required
to set a very low priority
but since Linux 2.6.25, this is no longer required.
A call to
must follow both rules, or the call will fail with the error
Glibc does not yet provide a suitable header file defining
the function prototypes and macros described on this page.
Suitable definitions can be found in
in the Linux kernel source tree
This page is part of release 5.10 of the Linux
A description of the project,
information about reporting bugs,
and the latest version of this page,
can be found at